Newfrog Printers Price in Singapore November, 2018

138 Products
_
×
We are working hard on getting this feature ready for you. Stay tuned!
Go to Shop −50%
Newfrog 3D Printer TMC2100 V1.3 Stepper Motor Driver Silent Mute Driver w/Heatsink
S$ 12.40 S$ 24.80
Newfrog

3D Printer TMC2100 V1.3 Stepper Motor Driver Mute Silent Stepper Driver Excellent Stability Protection with HeatsinkTMC2100V1.3 Description:1. MKS TMC2100 Step motor drive board super quiet drive StepStick compatible for Arduino with high working temperature.2. Without fans the working temperature is about 70 degrees at 0.5A and the working temperature of 1A is more than 150 degrees.3. It is possible to lose step. It is strongly required to do well in heat dissipation. The recommended working current is better than 0.5A.Driving current algorithm and regulation:1. Drive current algorithm: i=Vref*1.9/2.5 the default Vref is about 0.65v so the default current 0.5A the maximum current is 1A.2. Vref measures the voltage in the middle end of the Gnd and the potentiometer.3. When measuring the voltage do not connect the motor otherwise it is easy to burn down the drive.4. When measuring the voltage the power supply should be switched on. Do not only connect the USB power supply. Silent Stepper Descriptions:1. The Silent Stepper is mainly aimed at the vibrating marks produced by the 3D printer when the parallel arm structure is being printed especially using the TMC2100 drive and the low resistance motor.2. It can effectively eliminate unevenness signal waves in low speed conditions so as to achieve relatively smooth signal waves.3. The effect is most obvious in the use of the TMC2100 drive 24V power Delta.Note: Please allow 1-3mm differs due to manual measurement.Due to the different display and different light the picture may not show the actual color of the item. Thanks for your understand.

Read more
Go to Shop −38%
Newfrog Blue 220*220*0.3mm PEI Sheet for 3D Printing with 468MP Adhesive Tape 3d printer parts Polyetherimide sheet
S$ 7.10 S$ 11.50
Newfrog

Blue 220*220*0.3mm PEI Sheet for 3D Printing with 468MP Adhesive TapeDescriptions:PEI (Polyetherimide) sheets provide a 3D printing build surface that requires no tape slurry or adhesive. ABS and PLA both stick extremely well to the surface which eliminates the need for support rafts used for better adhesion. The printed 3D parts will adhere to the PEI surface on a heated bed and it will release or pop off when cooling down.Features:Great for printing ABS and PLA (along with many other materials) directly on to print surface without the need for additional adhesives or tape.Single 0.8mm sheet installs quickly on top of existing build platform.Protective film guards against scratches during shipping. Remove film from both sides before using PEI sheet.Reuse for multiple prints just wipe down with isopropyl alcohol between prints for best results.Works especially well with Delta style 3D printers.How to use:1. There are two methods to attaching the PEI to your print bed.2. The first method is to just clamp the sheet to the print bed using binder clips. The second method get 468MP Transfer Tape and use it to stick the PEI to the print bed.3. Once the PEI sheet is attached re-level your print bed and you are ready to go!4. It helps to wipe the surface down with isopropyl alcohol methyl alcohol or soap in between prints.5. This will ensure the PEI is clean and help adhesion. Light sanding with 2000 grit paper will also give the PEI sheet more life.Specifications:Color: BlueSize: approx.220*220*0.3mm/8.66*8.66*0.01''Note:Please allow 1-3mm differs due to manual measurement.Due to the different display and different light the picture may not reflect the actual color of the item. Thanks for your understanding.

Read more
Go to Shop
Newfrog Heated Bed Power Module Board Expansion Hot Bed MOS Tube for 3D Printer
S$ 11.70
Newfrog

High Power Heated Bed Power Module Board Expansion Hot Bed MOS Tube for 3D Printer Parts Description:1. If your total power is 240W and you have 12V power it means at least need 20A (20X12 = 240W).2. Because the controller panel can only set 15A this setting will not work. To make it work you need this additional power module.3. This module can be used in Chitu motherboard and other opened 3D printer motherboards.4. Under normal cooling conditions the module is found to be stable in operation at (Max) = 25A and the current should not exceed 25A.5. If you intend to use a heating bed and a 3D printer that uses a 12V power supply it is recommended to use this module otherwise it may lead to excessive current and may burn out the connector on the controller board.Feature:1. Universal heating bed power expansion module high power module for 3D printer.2. It can be used in Chitu motherboard and other opened 3D printer motherboards.3. Help to provide control panel (maximum 15A) 3D printer becomes more powerful.4. With this additional module the maximum current on the on board leads can reach 25A.Specification:Color: BlackProduct size: 120*50*30mm/4.72*1.96*1.18''Maximum current: 25A (enhanced heat dissipation)Note: Please allow slight size differs due to manual measurement.Due to the different display and different light the picture may not show the actual color of the item. Thanks for your understand.

Read more
Go to Shop −20%
Newfrog 3D Printer Parts Accessories LV8729 Stepper Motor Driver Mute Module+ Heat Sink Ultra-quiet Plug-in Drive Module
S$ 6.80 S$ 8.60
Newfrog

Product descriptions:LV8729 drive module has 128 segment. It is a ultra-quiet plug-in drive module which is especially researched and designed to meet customers' high segment driver. It is simple to operate and the best choice for printer to create a quiet environment.Features:1. In 64 subdivision or 128 subdivision to achieve a better ultra-quiet effect;2. Operating voltage: 6V-36V the proposed voltage is 12V;3. The maximum current is 1.5A the default is 0.8A;4. Segament: 1 1/2 1/4 1/8 1/16 1/32 1/64 1/128;5. You must add the heat sink to make the heat dissipation better (please be sure to operate with a large fan to help cooling).Specifications:Model: LV8729Type: stepper motor driverSize: 1.5mm x 2.0mmMaximum drive current: 1.8A (factory default 0.8A)Maximum voltage: 36V (usually 12V)Supported segament: 1 1/2 1/4 1/8 1/16 1/32 1/64 1/128Product craft: four-layer PCB boardProduct weight: 5gSegment settings table:The motherboard segmentation jumper caps from left to right are called M1 M2 M3. High when the jumper cap is plugged in and Low when the jumper cap is removed;After a lontg est the use of 64 segment works best.Drive current algorithm and regulation:1. Drive current algorithm: i = Vref/ 0.5 the default Vref is about 0.4V so the default current is 0.8A and the maximum current is 1.5A!2. Vref measures the voltage between Gnd and the potentiometer.3. When measuring the voltage you must not connect motor. Otherwise it will get easy to burn drive.4. It should be connected to the power supply when measuring voltage. Do not just connect USB power supply.5. When adjusting the drive potentiometer be sure to reduce the potentiometer; adjust again after measuring to avoid the current is too large leading to burned drive;6. Clockwise to increase anti-clockwise to reduce;LV8729 enhanced heat dissipation tips:Taking the heat issue into consideration LV8729 uses a four-layer PCB for overall cooling and the chip comes with a heat sink whose factory default drive current is 1A. Due to LV8729 drive subdivision is large for 3D printer stable operation any motor drive module should operate with active heat dissipation. The installation of fans and hanging cooling bracket or equip motherboard with a big fan.Notes:Please pay attention to the direction and you must not insert it reversely. Otherwise the chip will get damaged.The pin of the 8729 drive is blue and black.

Read more
Go to Shop −32%
Newfrog ALLOYSEED 3D Printer Parts Black 300*300*1.0mm PEI Sheet for 3D Printing with 468MP Adhesive Tape
S$ 18.50 S$ 27.30
Newfrog

Black 300*300*1.0mm PEI Sheet for 3D Printing with 468MP Adhesive TapeDescriptions:PEI (Polyetherimide) sheets provide a 3D printing build surface that requires no tape slurry or adhesive. ABS and PLA both stick extremely well to the surface which eliminates the need for support rafts used for better adhesion. The printed 3D parts will adhere to the PEI surface on a heated bed and it will release or pop off when cooling down.Features:Great for printing ABS and PLA (along with many other materials) directly on to print surface without the need for additional adhesives or tape.Single 0.8mm sheet installs quickly on top of existing build platform.Protective film guards against scratches during shipping. Remove film from both sides before using PEI sheet.Reuse for multiple prints just wipe down with isopropyl alcohol between prints for best results.Works especially well with Delta style 3D printers.How to use:1. There are two methods to attaching the PEI to your print bed. 2. The first method is to just clamp the sheet to the print bed using binder clips. The second method get 468MP Transfer Tape and use it to stick the PEI to the print bed.3. Once the PEI sheet is attached re-level your print bed and you are ready to go!4. It helps to wipe the surface down with isopropyl alcohol methyl alcohol or soap in between prints. 5. This will ensure the PEI is clean and help adhesion. Light sanding with 2000 grit paper will also give the PEI sheet more life.Specifications:Color: BlackSize: approx. 300*300*1.0mm/11.81*11.81*0.03''Note: Please allow 1-3mm differs due to manual measurement.Due to the different display and different light the picture may not reflect the actual color of the item. Thanks for your understanding.

Read more
Go to Shop −50%
Newfrog 10pcs Stepper Motor Heatsink+2pcs Thermal Conductive Plaster for 3D Printer
S$ 8.90 S$ 17.90
Newfrog

3D Printer Parts Stepper Motor Driver Cooling Block Heatsink for TMC2100/2130/220+Thermal Conductive Heatsink Plaster Adhesive Cooling Paste Stepper Motor Driver Cooling Block Specification:Color: BlueQuantity: 10pcsSize: 20*14*13mm/0.78*0.55*0.51''Application: for TMC2100/2130/2208/ LV8729 DRV8825 and so onThermal Conductive Heatsink Plaster Features:1. It has good conductivity and wide service temperature range(-60~200) short term 300 high temperature.2. The surface curing time is short the adhesive force is strong the storage period is long non-toxic and solvent free.3. It can be applied safely in elastic adhesion heat dissipation insulation and encapsulation in electronics electrical appliances instruments LED heat sinks and other industries.4. It is suitable for all kinds of components LED and heat dissipation devices which need to be bonded directly. It has high strength and fast adhesion effect.Thermal Conductive Heatsink Plaster Specifications:Product weight: 5gQuantity: 2pcsHeat conductive adhesive :white pasteThermal conductivity >0.671W/m.kBreaking strength 1.5MPASurface vulcanization time 10MIN /25Application: directly bonded solid components LED and heat dissipation devices etc.Use for : Chip CPU Memory North bridge South bridge VGA card Other heat dissipation partThermal Conductive Heatsink Plaster Operation Manual:1. When it is used the product is directly extruded rubbed and glued to the surface of the adhesive and then covered immediately after the test so as to be tried again.2. The surface fixed speed is related to the relative humidity and temperature in the air; the higher the temperature the faster the curing rate is the slower the vice versa.3. Recommended coating thickness: 0.1-0.5mm the thinner the better.4. Before use please clean with solvent (such as alcohol) adhesive surface detergents should be surface to be clean before painting.Note: Please allow 1-3mm differs due to manual measurement.Due to the different display and different light the picture may not show the actual color of the item. Thanks for your understand.

Read more
Go to Shop −29%
Newfrog 220 x 220 x 1mm Cold PEI 3D Printer Build Surface Polyetherimide PEI Sheet for 3D Printing with 468MP Adhesive Tape Wholesale
S$ 12.20 S$ 17.30
Newfrog

Descriptions:PEI (Polyetherimide) sheets provide a 3D printing build surface that requires no tape slurry or adhesive. ABS and PLA both stick extremely well to the surface which eliminates the need for support rafts used for better adhesion. The printed 3D parts will adhere to the PEI surface on a heated bed and it will release or pop off when cooling down.Features:Great for printing ABS and PLA (along with many other materials) directly on to print surface without the need for additional adhesives or tape.Single 0.8mm sheet installs quickly on top of existing build platform.Protective film guards against scratches during shipping. Remove film from both sides before using PEI sheet.Reuse for multiple prints just wipe down with isopropyl alcohol between prints for best results.Works especially well with Delta style 3D printers.How to use:There are two methods to attaching the PEI to your print bed. The first method is to just clamp the sheet to the print bed using binder clips. The second method get 468MP Transfer Tape and use it to stick the PEI to the print bed.Once the PEI sheet is attached re-level your print bed and you are ready to go!It helps to wipe the surface down with isopropyl alcohol methyl alcohol or soap in between prints. This will ensure the PEI is clean and help adhesion. Light sanding with 2000 grit paper will also give the PEI sheet more life.Specifications:Color: transparent clearSize: 220 x 220 x 1mm/8.66 x 8.66 x 0.04"

Read more
Go to Shop
Newfrog White 220 x 220 x 0.8mm PEI Sheet Polyetherimide sheets for 3D Printing with 468MP Adhesive Tape 3D printer parts
S$ 13.20
Newfrog

Descriptions:PEI (Polyetherimide) sheets provide a 3D printing build surface that requires no tape slurry or adhesive. ABS and PLA both stick extremely well to the surface which eliminates the need for support rafts used for better adhesion. The printed 3D parts will adhere to the PEI surface on a heated bed and it will release or pop off when cooling down.Features:Great for printing ABS and PLA (along with many other materials) directly on to print surface without the need for additional adhesives or tape.Single 0.8mm sheet installs quickly on top of existing build platform.Protective film guards against scratches during shipping. Remove film from both sides before using PEI sheet.Reuse for multiple prints just wipe down with isopropyl alcohol between prints for best results.Works especially well with Delta style 3D printers.How to use:1. There are two methods to attaching the PEI to your print bed. 2. The first method is to just clamp the sheet to the print bed using binder clips. The second method get 468MP Transfer Tape and use it to stick the PEI to the print bed.3. Once the PEI sheet is attached re-level your print bed and you are ready to go!4. It helps to wipe the surface down with isopropyl alcohol methyl alcohol or soap in between prints. 5. This will ensure the PEI is clean and help adhesion. Light sanding with 2000 grit paper will also give the PEI sheet more life.Specifications:Color: WhiteSize: approx. 220 x 220 x 0.8mm/8.66 x 8.66 x 0.03"Note: Please allow 1-3mm differs due to manual measurement.Due to the different display and different light the picture may not reflect the actual color of the item. Thanks for your understanding.

Read more
Go to Shop −46%
Newfrog ALLOYSEED 3D Printer Parts Black 220 x 220 x 0.8mm PEI Sheet for 3D Printing with 468MP Adhesive Tape
S$ 11.00 S$ 20.60
Newfrog

Descriptions:PEI (Polyetherimide) sheets provide a 3D printing build surface that requires no tape slurry or adhesive. ABS and PLA both stick extremely well to the surface which eliminates the need for support rafts used for better adhesion. The printed 3D parts will adhere to the PEI surface on a heated bed and it will release or pop off when cooling down.Features:Great for printing ABS and PLA (along with many other materials) directly on to print surface without the need for additional adhesives or tape.Single 0.8mm sheet installs quickly on top of existing build platform.Protective film guards against scratches during shipping. Remove film from both sides before using PEI sheet.Reuse for multiple prints just wipe down with isopropyl alcohol between prints for best results.Works especially well with Delta style 3D printers.How to use:There are two methods to attaching the PEI to your print bed. The first method is to just clamp the sheet to the print bed using binder clips. The second method get 468MP Transfer Tape and use it to stick the PEI to the print bed.Once the PEI sheet is attached re-level your print bed and you are ready to go!It helps to wipe the surface down with isopropyl alcohol methyl alcohol or soap in between prints. This will ensure the PEI is clean and help adhesion. Light sanding with 2000 grit paper will also give the PEI sheet more life.Specifications:Color: BlackSize: approx. 220 x 220 x 0.8mm/8.66 x 8.66 x 0.03"

Read more
Go to Shop
Newfrog 220 x 220 x 0.8mm PEI Sheet Single 0.8mm Polyetherimide sheet for 3D printer Printing with 468MP Adhesive Tape
S$ 13.40
Newfrog

Descriptions:PEI (Polyetherimide) sheets provide a 3D printing build surface that requires no tape slurry or adhesive. ABS and PLA both stick extremely well to the surface which eliminates the need for support rafts used for better adhesion. The printed 3D parts will adhere to the PEI surface on a heated bed and it will release or pop off when cooling down.Features:Great for printing ABS and PLA (along with many other materials) directly on to print surface without the need for additional adhesives or tape.Single 0.8mm sheet installs quickly on top of existing build platform.Protective film guards against scratches during shipping. Remove film from both sides before using PEI sheet.Reuse for multiple prints just wipe down with isopropyl alcohol between prints for best results.Works especially well with Delta style 3D printers.How to use:There are two methods to attaching the PEI to your print bed. The first method is to just clamp the sheet to the print bed using binder clips. The second method get 468MP Transfer Tape and use it to stick the PEI to the print bed.Once the PEI sheet is attached re-level your print bed and you are ready to go!It helps to wipe the surface down with isopropyl alcohol methyl alcohol or soap in between prints. This will ensure the PEI is clean and help adhesion. Light sanding with 2000 grit paper will also give the PEI sheet more life.Specifications:Color: transparent clearSize: 220 x 220 x 0.8mm/8.66 x 8.66 x 0.03"

Read more
Go to Shop −38%
Newfrog 1m/3.3ft HT-NTC100K Thermistor Temperature Sensor for 3D Printer Filament
S$ 3.50 S$ 5.70
Newfrog

3D Printer Parts 1m/3.3ft HT-NTC100K Thermistor Temperature Sensor for High Temperature Filament 350 Degrees350 Degrees HT-NTC100K Thermistor High Temperature Sensor Replace K-type Thermocouple for 3D Printer Features:1. Resistance package temperature measurement the external diameter of the cylinder is 3mm and the length is 15mm. It can be used to support the heating of the thermocouple.2. From the original range of temperature measurement -50 to +350 power assisted printing high temperature material.3. The use of 304 stainless steel combined with internal temperature measurement and packaging to achieve maximum service life and accurate temperature measurement.4. The white high temperature wire cord higher temperature resistance using plying line connection not easy to break.5. It can be used with the new heating tube (the new heating pipe can be heated up to about 350 degrees).6. The measuring temperature can reach 350 degrees which can effectively replace the K thermocouple. 7. It solves the problem that the K type thermocouple has strict requirements for wiring the line is too long and the temperature fluctuation is too large and so on which affects the printing quality.Specifications:Model: HT-NTC100KColor: WhiteCable length: approx. 1m/3.3ft Net weight: approx. 7gNote: Please allow 1-3mm differs due to manual measurement.Due to the different display and different light the picture may not show the actual color of the item. Thanks for your understanding.

Read more
Go to Shop
Newfrog 200x200x0.3mm PEI Sheet Polyetherimide Surface for 3D Printer with Adhesive
S$ 9.40
Newfrog

200x200x0.3mm PEI Sheet Polyetherimide Build Surface for 3D Printer with 468MP Adhesive TapeDescription:1. PEI (polyether imide) is an amber transparent solid. Without adding any additives PEI particles have inherent flame retardancy and low smoke. The oxygen index is 47% the combustion grade is UL94-V-0 and the density is 1.28~1.42g/cm3.2. PEI has strong high temperature stability even if it is non reinforced PEI it has good toughness and strength. Therefore the use of PEI's superior thermal stability can be used to make high temperature and heat-resistant devices.3. It has excellent mechanical properties electrical insulation radiation resistance high and low temperature resistance and wear resistance and can be transmitted through microwave.4. The PEI board is a non crystalline plastic. It is an amorphous high performance polymer which is made of an amorphous PEI (polyether imide) engineering plastics through a high temperature extruder.5. PEI (polyether imide) provides a 3D printing build surface that does not require a slurry or adhesive.6. ABS and PLA can be maintained very well on the surface so that no supporting rafts are needed for better adhesion.7. The 3D part of the print will be attached to the surface of the PEI on the heating bed which will be released or ejected when cooling.Features:1. 468MP adhesive tape is sticked.2. Printing ABS and PLA (together with many other materials) directly to the printed surface without additional adhesives or tapes.3. Repeated use of multiple printing only the use of isopropanol wiping between the print can get the best effect.Specifications:Color: AmberProduct size: approx.200*200*0.3mm/7.87*7.87*0.01''Operation Manual:1. Use a loose-leaf binder to fix the paper on the printing bed.2. Attach PEI to a printing lathe.Note: Please allow 1-3cm differs due to manual measurement.Due to the different display and different light the picture may not show the actual color of the item. Thanks for your understanding.

Read more
Go to Shop −18%
Newfrog 3D Printer Kit Parts RAMPS 1.4 MEGA2560 A4988 LCD 12864 Controller Board with Arduino-Compatible Mega 2560 R3 for RepR
S$ 38.50 S$ 47.40
Newfrog

RAMPS1.4 Kit +Mega2560+5pcs A4988+LCD 12864 Display For 3D Printer RepRap Features:1.3D Printer Controller RAMPS 1.4The RAMPS 1.4 board is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service part replacement upgrade-ability and expansion. Additionally a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.2.Arduino-Compatible Mega 2560 R3Fully compatible with original Arduino MEGA 2560 R3 with this product you are able to use all the Arduino open source platform to create or learn interactive objects it will be a lot of fun while you are creating and learning it so just get this and start it we also provide reference pdf files that can help you to improve skills very quickly. after all time matters the sooner you can improve your programing skills the sooner you can create amazing projects!Compared with UNO R3 this is with main Chip ATmega2560 with more I/O Pins and additional 10 PWM output of course the EEPROM is also with larger space.3.A4988 StepStick Compatible Stepper Motor Driver ModuleA4988 driver is a carrier board or breakout board for Allegro's A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil.4.RAMPS LCD12864 controllerThis full graphic Smart Controller contains a SD-Card reader an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the "smart adapter" included. After connecting this panel to your Ramps you don't need your pc any more the Smart Controller supplies power for your SD card. Further more all actions like calibration axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC just with a g-code design stored on the SD card.

Read more
Go to Shop
Newfrog 220x220x0.3mm PEI Sheet Polyetherimide Surface for 3D Printer with Adhesive
S$ 10.10
Newfrog

220x220x0.3mm PEI Sheet Polyetherimide Build Surface for 3D Printer with 468MP Adhesive TapeDescription:1. PEI (polyether imide) is an amber transparent solid. Without adding any additives PEI particles have inherent flame retardancy and low smoke. The oxygen index is 47% the combustion grade is UL94-V-0 and the density is 1.28~1.42g/cm3.2. PEI has strong high temperature stability even if it is non reinforced PEI it has good toughness and strength. Therefore the use of PEI's superior thermal stability can be used to make high temperature and heat-resistant devices.3. It has excellent mechanical properties electrical insulation radiation resistance high and low temperature resistance and wear resistance and can be transmitted through microwave.4. The PEI board is a non crystalline plastic. It is an amorphous high performance polymer which is made of an amorphous PEI (polyether imide) engineering plastics through a high temperature extruder.5. PEI (polyether imide) provides a 3D printing build surface that does not require a slurry or adhesive.6. ABS and PLA can be maintained very well on the surface so that no supporting rafts are needed for better adhesion.7. The 3D part of the print will be attached to the surface of the PEI on the heating bed which will be released or ejected when cooling.Features:1. 468MP adhesive tape is sticked.2. Printing ABS and PLA (together with many other materials) directly to the printed surface without additional adhesives or tapes.3. Repeated use of multiple printing only the use of isopropanol wiping between the print can get the best effect.Specifications:Color: AmberProduct size: approx.220*220*0.3mm/8.66*8.66*0.01''Operation Manual:1. Use a loose-leaf binder to fix the paper on the printing bed.2. Attach PEI to a printing lathe.Note: Please allow 1-3cm differs due to manual measurement.Due to the different display and different light the picture may not show the actual color of the item. Thanks for your understanding.

Read more

Newfrog Printers Singapore

Popular models for Printers from Newfrog are usually from the 3D Printer TMC2100 V1.3 Stepper Motor Driver Silent Mute Driver w/Heatsink, 330m/1082ft 3D Printer Filament ABS 1.75mm Consumables(Grass Green) and 220x220x0.5mm Blue Heated Bed Square Frosted Hot Bed Sticker for 3D Printer collection. If you are not sure about having Newfrog Printers, you might want to check out the products from louis will, HP and Epson. On iPrice Singapore, you can find your ideal Newfrog Printers for as low as S$ 2.00 up to as much as S$ 41.00. iPrice Singapore has a wide range of Newfrog Printers that would suit your needs. We offer a wide range of Newfrog Printers with discounts of up to 58%!